Search Results

Search Again
Page 1 of 9
  1. craig moss
    Post

    best bearings for a bbc bown alc

    This is in a jet boat we don't shift the rpm goes up and stays there. Callies magnum crank ,Oliver heavyweight rods with bolt upgrade, Dart big m...
    Post by: craig moss, Jul 10, 2009 in forum: PSI Superchargers Tech Questions
  2. craig moss
    Post

    Psycho-Helix rotors

    I called about a month ago. They said they were behind schedule on that project. Aug or Sept
    Post by: craig moss, Jul 10, 2009 in forum: PSI Superchargers Tech Questions
  3. craig moss
    Thread

    best bearings for a bbc bown alc

    What would be the best bearings to use?? We do not tear down but once a year. 35-40 boost THANKS CRAIG
    Thread by: craig moss, Jul 9, 2009, 10 replies, in forum: PSI Superchargers Tech Questions
  4. craig moss
    Post

    TOO much boost at 10% od ??

    Anyone else ???? Need more input thanks everyone !!! Craig:confused:
    Post by: craig moss, Jul 9, 2009 in forum: PSI Superchargers Tech Questions
  5. craig moss
    Post

    Weather Station

    Same here works great and water proof :cool:
    Post by: craig moss, Jul 6, 2009 in forum: PSI Superchargers Tech Questions
  6. craig moss
    Thread

    TOO much boost at 10% od ??

    I have a friend with a 548 BBC brodix big brodie 2 heads no port work. It was originally set up for an 8-71. Cam is dur@50 285-288 valve timing...
    Thread by: craig moss, Jul 3, 2009, 3 replies, in forum: PSI Superchargers Tech Questions
  7. craig moss
    Post

    Right-Stuff vs. injector gaskets

    clear, black, orange, blue, gray hi temp low temp used all of them no problem. It is hard to take it apart
    Post by: craig moss, Jul 1, 2009 in forum: PSI Superchargers Tech Questions
  8. craig moss
    Post

    high speed

    I run mine on top of the shut off
    Post by: craig moss, Jun 25, 2009 in forum: PSI Superchargers Tech Questions
  9. craig moss
    Post

    How much boost should I expect?

    I had a std kuhl with the delta bottom. 35od made 25 psi bbc same flow numbers Mike is spot on! I bet it makes about 8- 10 psi at 0 od just a...
    Post by: craig moss, Jun 25, 2009 in forum: PSI Superchargers Tech Questions
  10. craig moss
    Post

    Brooks rods,read this before you buy

    Bad customer service !!!!! That is a load of Sh$t!! I would e-mail them this thread and tell them the internet is a powerful tool, and how many...
    Post by: craig moss, Jun 24, 2009 in forum: PSI Superchargers Tech Questions
  11. craig moss
    Post

    changing combo need help

    THANKS WILL YOU DA MAN !!!:cool:
    Post by: craig moss, Jun 23, 2009 in forum: PSI Superchargers Tech Questions
  12. craig moss
    Post

    Cool em down

    I wonder if you used the blow side of the shop vac SEEMS SAFER
    Post by: craig moss, Jun 23, 2009 in forum: PSI Superchargers Tech Questions
  13. craig moss
    Post

    Cool em down

    I wouldn't stand too close to the shop vac. They make a lot of static electricity :eek:BOOM
    Post by: craig moss, Jun 22, 2009 in forum: PSI Superchargers Tech Questions
  14. craig moss
    Post

    How much overdrive is max with a Kobelco

    I have been told that 12500-13000 max rotor speed. So i ask 70% over what crank shaft rpm hope it helps
    Post by: craig moss, Jun 21, 2009 in forum: PSI Superchargers Tech Questions
  15. craig moss
    Post

    When is a PM appropriate?

    I bet most of the time the pms are a phone number it is hard to explain some things typing( A LOT EASIER ON THE PHONE just my guess )
    Post by: craig moss, Jun 20, 2009 in forum: PSI Superchargers Tech Questions
  16. craig moss
    Post

    changing combo need help

    What would be the best deck height?? I am starting from scratch I may as well go big if its feasible
    Post by: craig moss, Jun 20, 2009 in forum: PSI Superchargers Tech Questions
  17. craig moss
    Thread

    changing combo need help

    I just found out my crank is cracked.So I am changing directions what is the best deck height block/rod length/stroke/bore combo ? going to run...
    Thread by: craig moss, Jun 19, 2009, 8 replies, in forum: PSI Superchargers Tech Questions
  18. craig moss
    Post

    Finding TDC hopefully I did this right!

    I use a torque wrench So if the stop is off center of the wrist pin you can accurately take in to account piston to wall clearance, as well as rod...
    Post by: craig moss, Jun 17, 2009 in forum: PSI Superchargers Tech Questions
  19. craig moss
    Post

    Fuel - Hat vs. Intake

    have it flowed www.fuelinjectionenterprises.com it will pay for itself:cool:
    Post by: craig moss, Jun 17, 2009 in forum: PSI Superchargers Tech Questions
  20. craig moss
    Post

    best place to buy nozzle jets?

    Spud all the way he is as honest as they come. I would highly recommend him on flowing systems and mag work check out his site...
    Post by: craig moss, Jun 9, 2009 in forum: PSI Superchargers Tech Questions
Showing results 1 to 20 of 161 Next >
Search Again
Page 1 of 9