Search Results

Search Again
Page 1 of 2
  1. Mike sparks
    Post

    Tune

    Ok so what tune combination should I run
    Post by: Mike sparks, Nov 6, 2016 in forum: PSI Superchargers Tech Questions
  2. Mike sparks
    Post

    Tune

    And I have a 3# spring in the idle check
    Post by: Mike sparks, Nov 6, 2016 in forum: PSI Superchargers Tech Questions
  3. Mike sparks
    Thread

    Tune

    427 .030 Bbc , 6-71 standard helix, bug catcher with enderle 110 pump and 6 amp don zig vertex mag running 36 degrees of timing and have 57 hat...
    Thread by: Mike sparks, Nov 6, 2016, 6 replies, in forum: PSI Superchargers Tech Questions
  4. Mike sparks
    Post

    Timing

    My compression is 11:1
    Post by: Mike sparks, Nov 2, 2016 in forum: PSI Superchargers Tech Questions
  5. Mike sparks
    Post

    Timing

    I ran 32 before the magneto now running 36 and so far it sounds crazy at idle
    Post by: Mike sparks, Nov 1, 2016 in forum: PSI Superchargers Tech Questions
  6. Mike sparks
    Post

    Timing

    Also a 6 amp mag
    Post by: Mike sparks, Nov 1, 2016 in forum: PSI Superchargers Tech Questions
  7. Mike sparks
    Thread

    Timing

    what should my timing be set at for my 427 Bbc 22 lbs of boost on alcohol
    Thread by: Mike sparks, Nov 1, 2016, 5 replies, in forum: PSI Superchargers Tech Questions
  8. Mike sparks
    Post

    Ignition

    I'm not sure when it starts boosting but it comes in real quick. It's been hard to get traction so with more converter I think my traction issues...
    Post by: Mike sparks, Oct 16, 2016 in forum: PSI Superchargers Tech Questions
  9. Mike sparks
    Post

    Ignition

    3400 lbs car the best 60ft was 1.36
    Post by: Mike sparks, Oct 15, 2016 in forum: PSI Superchargers Tech Questions
  10. Mike sparks
    Post

    Ignition

    Powerglide 1.76 planetary
    Post by: Mike sparks, Oct 15, 2016 in forum: PSI Superchargers Tech Questions
  11. Mike sparks
    Post

    Ignition

    3000-3200 I'm running a 3500 stall
    Post by: Mike sparks, Oct 15, 2016 in forum: PSI Superchargers Tech Questions
  12. Mike sparks
    Post

    Ignition

    Gm block and nitrid steel crank
    Post by: Mike sparks, Oct 15, 2016 in forum: PSI Superchargers Tech Questions
  13. Mike sparks
    Post

    Ignition

    Is there any dangers using my 2step to launch the car?
    Post by: Mike sparks, Oct 14, 2016 in forum: PSI Superchargers Tech Questions
  14. Mike sparks
    Post

    Ignition

    My car is all steel and window glass all steel wheel tubs and trunk And floor. The fastest it went was 6.01@120mph 1/8 mile
    Post by: Mike sparks, Oct 13, 2016 in forum: PSI Superchargers Tech Questions
  15. Mike sparks
    Post

    Ignition

    My email is mikej72984@aol.com or text 5132645977
    Post by: Mike sparks, Oct 13, 2016 in forum: PSI Superchargers Tech Questions
  16. Mike sparks
    Post

    Ignition

    What about heat in the engine? After an 1/8 mile pass I'm 170 degrees if I lean out more will it cause more heat?
    Post by: Mike sparks, Oct 13, 2016 in forum: PSI Superchargers Tech Questions
  17. Mike sparks
    Post

    Ignition

    The plugs look clean and have a little color change half way up the ground strap
    Post by: Mike sparks, Oct 13, 2016 in forum: PSI Superchargers Tech Questions
  18. Mike sparks
    Post

    Ignition

    Gapping the plugs got me another 1000 rpm. I found a 7al real cheap and going to buy the 2amp coil and try that out for now
    Post by: Mike sparks, Oct 11, 2016 in forum: PSI Superchargers Tech Questions
  19. Mike sparks
    Post

    Ignition

    ok cool I will see what it does tomorrow
    Post by: Mike sparks, Oct 7, 2016 in forum: PSI Superchargers Tech Questions
  20. Mike sparks
    Post

    Ignition

    Timing is at 32 degrees
    Post by: Mike sparks, Oct 7, 2016 in forum: PSI Superchargers Tech Questions
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2