Search Results

Search Again
Page 5 of 5
  1. 3-D
    Post

    Cold lash setting on billet block?

    i have .014 with a Rodek and conventional BBC heads
    Post by: 3-D, May 13, 2009 in forum: PSI Superchargers Tech Questions
  2. 3-D
    Post

    Small primer pump??

    poppet I have seen the poppet and was going to try it. But my concern for keeping it closed after start up was the main concern. Any info on...
    Post by: 3-D, May 7, 2009 in forum: PSI Superchargers Tech Questions
  3. 3-D
    Post

    Another timing question

    timing what do you guys think about timing in a 540, 12.3:1 compression, conventional BBC heads, 8-71 Kobelco 20-30% over, for timing? thanks
    Post by: 3-D, Apr 30, 2009 in forum: PSI Superchargers Tech Questions
  4. 3-D
    Post

    12volt vs. 16volt

    i absolutly will not go back to a 12v battery since experiencing my 16v set up. I have had it for almost 2 years now. Everything runs better,...
    Post by: 3-D, Apr 20, 2009 in forum: PSI Superchargers Tech Questions
  5. 3-D
    Post

    blower output in cu in

    you state cfm, what about cubic inches per revolution
    Post by: 3-D, Apr 15, 2009 in forum: PSI Superchargers Tech Questions
  6. 3-D
    Post

    Compression Ratio vs. Boost

    you state cfm, what about cubic inches per revolution
    Post by: 3-D, Apr 15, 2009 in forum: PSI Superchargers Tech Questions
  7. 3-D
    Post

    Compression Ratio vs. Boost

    compression I have a new 540 with 12.39 compression in a conventional headed BBC. I also have that program. the answer I need is the cu in per...
    Post by: 3-D, Apr 15, 2009 in forum: PSI Superchargers Tech Questions
  8. 3-D
    Thread

    blower output in cu in

    I have a Kobelco 8-71 Superman and need to know the cubic inches per revolution. Can anyone help me with that? thanks
    Thread by: 3-D, Apr 15, 2009, 19 replies, in forum: PSI Superchargers Tech Questions
  9. 3-D
    Post

    spark plug and gap recommendations

    responses i have static compression at 12.3:1 I run a "V" 16v battery There is a cable running from the grounding lug on the rear of the...
    Post by: 3-D, Mar 20, 2009 in forum: PSI Superchargers Tech Questions
  10. 3-D
    Post

    spark plug and gap recommendations

    Msd I have seen many others run a 7AL-3 and decided I would try it before investing in a complete new system. This is still going to be a...
    Post by: 3-D, Mar 19, 2009 in forum: PSI Superchargers Tech Questions
  11. 3-D
    Thread

    spark plug and gap recommendations

    I am doing blown alky for the first time. 540 BBC with conventional heads, 8-71 Superman blower, about 20-30% overdrive. What plugs do you guys...
    Thread by: 3-D, Mar 19, 2009, 11 replies, in forum: PSI Superchargers Tech Questions
  12. 3-D
    Post

    Throttle Return Bracket

    throttle return spring I could not find one, but made one very easy with a pieces of flat steel bent on a 90 degree and bolted it to the bottom...
    Post by: 3-D, Mar 18, 2009 in forum: PSI Superchargers Tech Questions
  13. 3-D
    Post

    Fuel Filters?

    filter when a filter is used just above the fuel pump, does all the "stuff" that gets trapped in the screen not go back through the fuel pump...
    Post by: 3-D, Mar 17, 2009 in forum: PSI Superchargers Tech Questions
  14. 3-D
    Post

    Can an injector be too big?

    too big? can you go too big on a blower injector. I just got a B&U 5.567 plates on a 540 BBC with a 8-71 superman. What are the difference's...
    Post by: 3-D, Mar 17, 2009 in forum: PSI Superchargers Tech Questions
  15. 3-D
    Post

    Throttle Stop Question

    you need an air on / air off throttle stop and they can work in both directions
    Post by: 3-D, Mar 17, 2009 in forum: PSI Superchargers Tech Questions
Find older messages
Showing results 81 to 95 of 95
Search Again
Page 5 of 5