Search Results

Search Again
Page 3 of 7
  1. Andy C
    Thread

    Screw Quill Shaft

    I need to get a quill shaft 4.025 for our screw... Who should I call?
    Thread by: Andy C, Apr 18, 2014, 2 replies, in forum: PSI Superchargers Tech Questions
  2. Andy C
    Post

    Looking for a SBC gear drive that allows BBC snout or Chrysler snout

    chain we had 2 SBC with BBC snout one was with Jesel belt the other with Chain both with 14/71 hh 35 over with no problems
    Post by: Andy C, Mar 19, 2014 in forum: PSI Superchargers Tech Questions
  3. Andy C
    Post

    Idler pulley ideas for whipple r980 on a bbc will b using water pump

    cooling system If you are going to run water, the best way to cool the engine is with reverse flow, put water in the heads and take it out from...
    Post by: Andy C, Mar 4, 2014 in forum: PSI Superchargers Tech Questions
  4. Andy C
    Post

    Idler pulley ideas for whipple r980 on a bbc will b using water pump

    water in block I would not run water in block... we have done it for years, just leave all water passages open... if you want to run water moroso...
    Post by: Andy C, Mar 3, 2014 in forum: PSI Superchargers Tech Questions
  5. Andy C
    Post

    BBC Gear Drive +.600 who makes one.

    rcd has +.400 not + 0.600
    Post by: Andy C, Jan 30, 2014 in forum: PSI Superchargers Tech Questions
  6. Andy C
    Thread

    BBC Gear Drive +.600 who makes one.

    I am looking for a BBC gear drive with raised cam + .600 who makes one. thanks Andy 845-323-2469
    Thread by: Andy C, Jan 28, 2014, 5 replies, in forum: PSI Superchargers Tech Questions
  7. Andy C
    Post

    who has had throttle stick ?

    throttle stuck we had the same thing happen to us could not find anything wrong... see vid yes tried to pull the throttle back with toe, lucky...
    Post by: Andy C, Jan 28, 2014 in forum: PSI Superchargers Tech Questions
  8. Andy C
    Post

    Ring help

    Rings Call Bruce Walker - Tel: (661) 775-2775 Cell: (661) 803-1089 Tell him Andy from NY gave you the #... Trust me you will thank me later...
    Post by: Andy C, Jan 19, 2014 in forum: PSI Superchargers Tech Questions
  9. Andy C
    Post

    supercharger guru question

    6x71 6x71 will move more air... pump up the eng comp...
    Post by: Andy C, Oct 13, 2013 in forum: PSI Superchargers Tech Questions
  10. Andy C
    Post

    thottle control

    throttle yes you will be able to open to your pre-set. if you put a on/off switch between trans brake. you can just press the throttle control...
    Post by: Andy C, Sep 30, 2013 in forum: PSI Superchargers Tech Questions
  11. Andy C
    Post

    rossler 210 vs lencodrive or bruno

    Rossler Rossler all the way... He makes mutiple gear sets... Had it for years without any problems, we run a screw at 3000lbs
    Post by: Andy C, Sep 3, 2013 in forum: PSI Superchargers Tech Questions
  12. Andy C
    Post

    weak BAE5 screw converter setup

    Please share Please share... we rum similar set up... 2950lbs
    Post by: Andy C, Jul 14, 2013 in forum: PSI Superchargers Tech Questions
  13. Andy C
    Post

    Hampton two lobe twisted rotor super 2 blower

    This x2, outlaw ???
    Post by: Andy C, Jul 12, 2013 in forum: PSI Superchargers Tech Questions
  14. Andy C
    Post

    Over-sized 1.094 piston pins

    pins Thank you everybody, i called trend, a little pricy... need to find cost effective...
    Post by: Andy C, Jun 29, 2013 in forum: PSI Superchargers Tech Questions
  15. Andy C
    Post

    powergrid and points box

    Timing Problem the timing was not steady, it was all over the place during the run. i record my actual timing during the run.
    Post by: Andy C, Jun 29, 2013 in forum: PSI Superchargers Tech Questions
  16. Andy C
    Post

    powergrid and points box

    Power grid do a search on here, or yellowbullet.com, we had a Power grid, and got rid of it, nothing but problems.... 8973 works ...
    Post by: Andy C, Jun 28, 2013 in forum: PSI Superchargers Tech Questions
  17. Andy C
    Thread

    Over-sized 1.094 piston pins

    I am looking for over-sized pins. now have 1.094 need 1.09??? what is out there? who makes them? have few sets of rods that i am looking to...
    Thread by: Andy C, Jun 28, 2013, 4 replies, in forum: PSI Superchargers Tech Questions
  18. Andy C
    Post

    Barrel Valve Spool

    Spool Call enderly, they can sell you the spool you need or BV. we run r/s BV
    Post by: Andy C, Jun 13, 2013 in forum: PSI Superchargers Tech Questions
  19. Andy C
    Post

    input shaft magnet

    magnets http://www.kjmagnetics.com/ make sure u buy neodymium magnets.
    Post by: Andy C, Jun 2, 2013 in forum: PSI Superchargers Tech Questions
  20. Andy C
    Post

    New Century block.

    Cam Call the cam co. and ask them the difference, we run a 60mm in BBC with .937 lifter .850 roller, 450lbs on the seat.
    Post by: Andy C, May 30, 2013 in forum: PSI Superchargers Tech Questions
Showing results 41 to 60 of 131 Next >
Search Again
Page 3 of 7