Search Results

Search Again
Page 4 of 9
  1. Mark Leigh
    Post

    Flywheel recert failed due to time passing....

    I had problems with that guy in 1996 --can't believe he is still in business ---- no people skills then
    Post by: Mark Leigh, Mar 28, 2015 in forum: PSI Superchargers Tech Questions
  2. Mark Leigh
    Post

    Best air pressure gauge for tires

    Ditto on the Moroso gauge -- it glows in the dark too !
    Post by: Mark Leigh, Mar 26, 2015 in forum: Pit Buzz
  3. Mark Leigh
    Post

    rpm's up = oil pressure drop? ;-(

    Agree with above post, you should not be using braided hose between the pan and pump -- should be hydraulic suction hose with the red , green or...
    Post by: Mark Leigh, Mar 25, 2015 in forum: PSI Superchargers Tech Questions
  4. Mark Leigh
    Post

    rpm's up = oil pressure drop? ;-(

    Priority oiling is a second oil galley in the back of the block on the left side of the cam as looking at from the drivers seat -- the galley can...
    Post by: Mark Leigh, Mar 24, 2015 in forum: PSI Superchargers Tech Questions
  5. Mark Leigh
    Post

    rpm's up = oil pressure drop? ;-(

    Has this engine combo ever had good oil pressure before or is it a new setup that has a problem ? Also is the block setup for priority oiling ?
    Post by: Mark Leigh, Mar 20, 2015 in forum: PSI Superchargers Tech Questions
  6. Mark Leigh
    Post

    leanout on 2step

    Standard K type sensors are 1/4 inch dia --
    Post by: Mark Leigh, Mar 10, 2015 in forum: PSI Superchargers Tech Questions
  7. Mark Leigh
    Post

    how to get 48 volts

    I give up ---
    Post by: Mark Leigh, Mar 7, 2015 in forum: PSI Superchargers Tech Questions
  8. Mark Leigh
    Post

    how to get 48 volts

    https://www.google.com/search?q=how+to+wire+4+12+volt+batteries+in+series&espv=2&biw=1067&bih=533&tbm=isch&imgil=ug-TKryEZU3x7M%253A%253Bn6bDROG0sW...
    Post by: Mark Leigh, Mar 5, 2015 in forum: PSI Superchargers Tech Questions
  9. Mark Leigh
    Post

    System One Dry Sump Pump plumbing issue

    Yes Will that is correct - I am going to use two 92 degree fittings from the RCD plumbing kit that attatch to the oil pan to make one 180 bend ------
    Post by: Mark Leigh, Feb 19, 2015 in forum: PSI Superchargers Tech Questions
  10. Mark Leigh
    Thread

    System One Dry Sump Pump plumbing issue

    I have a System One dry sump pump I am installing ---- the 180 bend that is 5 inch CLR won't fit due to the chassis upright location -- How...
    Thread by: Mark Leigh, Feb 18, 2015, 3 replies, in forum: PSI Superchargers Tech Questions
  11. Mark Leigh
    Thread

    Push button switch needed

    Who makes a nice switch to mount on the steering wheel of a FC for a mag retard that needs air on both sides of the cylinder ?
    Thread by: Mark Leigh, Jan 30, 2015, 1 replies, in forum: PSI Superchargers Tech Questions
  12. Mark Leigh
    Post

    weather station , drive shaft etc

    Make offers
    Post by: Mark Leigh, Jan 26, 2015 in forum: Noonan Classifieds
  13. Mark Leigh
    Post

    Rear Disk Brake Residual Valve

    I've had a Strange setup in both steel and CF----- I has a short firm pull ---- when they are bled properly ---- is your lever ratio correct ?
    Post by: Mark Leigh, Jan 19, 2015 in forum: PSI Superchargers Tech Questions
  14. Mark Leigh
    Post

    Rear Disk Brake Residual Valve

    You should not need to do this to get a firm handle -- You need to revisit how you bleed your brakes ---- what master cylinder setup do you have...
    Post by: Mark Leigh, Jan 19, 2015 in forum: PSI Superchargers Tech Questions
  15. Mark Leigh
    Post

    weather station , drive shaft etc

    Make offers
    Post by: Mark Leigh, Jan 14, 2015 in forum: Noonan Classifieds
  16. Mark Leigh
    Post

    Crank Hub

    You can use loctite to set it up -
    Post by: Mark Leigh, Jan 12, 2015 in forum: PSI Superchargers Tech Questions
  17. Mark Leigh
    Post

    Crank Hub

    Did you damage your crank snout ? How much smaller are you thinking ?
    Post by: Mark Leigh, Jan 11, 2015 in forum: PSI Superchargers Tech Questions
  18. Mark Leigh
    Post

    Don Williamson passes

    RIP Don, he always answered questions for me ---- one of the good guys
    Post by: Mark Leigh, Dec 30, 2014 in forum: Pit Buzz
  19. Mark Leigh
    Post

    weather station , drive shaft etc

    Bump Please
    Post by: Mark Leigh, Dec 27, 2014 in forum: Noonan Classifieds
  20. Mark Leigh
    Post

    weather station , drive shaft etc

    Changes made to list
    Post by: Mark Leigh, Dec 19, 2014 in forum: Noonan Classifieds
Showing results 61 to 80 of 171 Next >
Search Again
Page 4 of 9