Recent Content by quickcut

  1. quickcut
    Post

    Enderle Injection Tuning Help

    Seams your a long way out . You had the pump Flowed. Why did you buy a tune up as well then you will have a nozzles area with main size to start...
    Post by: quickcut, May 31, 2024 in forum: PSI Superchargers Tech Questions
  2. quickcut
    Post

    HEMI oil pump drive

    Broke 1 side of the tang in a super mag hemi 10 years ago. Done know why in the burn out
    Post by: quickcut, Sep 17, 2020 in forum: PSI Superchargers Tech Questions
  3. quickcut
    Post

    Fixing a crack in a Crankshaft

    Australia
    Post by: quickcut, Feb 11, 2020 in forum: PSI Superchargers Tech Questions
  4. quickcut
    Post

    Fixing a crack in a Crankshaft

    Ok Sorry to jump the thread. Who is the best to send a crank to for repair ? Mine has a big gouge in it.but it is not cracked. I want welded &...
    Post by: quickcut, Feb 11, 2020 in forum: PSI Superchargers Tech Questions
  5. quickcut
    Post

    KB head studs, where to find/buy

    John, Try Good Vibrations or RBS
    Post by: quickcut, Jan 13, 2020 in forum: PSI Superchargers Tech Questions
  6. quickcut
    Thread

    Manley Nex Tex Valve Springs 221451

    Just wondering Why was the Manley Nex Tex Valve triple spring 221451 discontinued Dose anyone why? Or was this spring Good or Bad was there a problem
    Thread by: quickcut, Dec 10, 2019, 0 replies, in forum: PSI Superchargers Tech Questions
  7. quickcut
    Post

    is an 80a good enough

    Bob Where are you ? I have Flowed 110 pumps Call me Dave 0419196725 Sydney
    Post by: quickcut, Nov 11, 2019 in forum: PSI Superchargers Tech Questions
  8. quickcut
    Post

    Oiling problem

    Heads Are Stage 3 AJPE Ex top fuel 1.75 ratio stage 5 BAE intake rockers Fired motor again today & burnt 4 intakes on the right hand side Dose...
    Post by: quickcut, Aug 30, 2019 in forum: PSI Superchargers Tech Questions
  9. quickcut
    Post

    Oiling problem

    Will, Have opened the cam up. If that doesn't work. I can feed from the back of the block, But where do I run it to? Make a Spray bar ?
    Post by: quickcut, Aug 28, 2019 in forum: PSI Superchargers Tech Questions
  10. quickcut
    Post

    Oiling problem

    yes block has been repaired & cleaned . No restrictors .Air has been blowen through everthing.
    Post by: quickcut, Aug 26, 2019 in forum: PSI Superchargers Tech Questions
  11. quickcut
    Post

    Oiling problem

    pull the cam today & check the holes In the bearing to the holes to the heads all good there so. dropped the sump & put the pick line in a bucket...
    Post by: quickcut, Aug 26, 2019 in forum: PSI Superchargers Tech Questions
  12. quickcut
    Thread

    Oiling problem

    Need some ideas where to start looking. Have a new build with a oiling problem I have very little oil coming up to the heads. Not enough. Bae hemi...
    Thread by: quickcut, Aug 24, 2019, 13 replies, in forum: PSI Superchargers Tech Questions
  13. quickcut
    Post

    Brad 3 hemi fats heads

    John, Message sent I am in Australia as well, I buy stuff from the USA all the time if cost us more like 69 cent to the us dollar so that will...
    Post by: quickcut, Jul 25, 2019 in forum: PSI Superchargers Tech Questions