Recent Content by bryanbrown

  1. bryanbrown
    Post

    Racepak, Crower 10.7, misc

    Bump
    Post by: bryanbrown, Jan 24, 2018 in forum: Noonan Classifieds
  2. bryanbrown
    Post

    Racepak, Crower 10.7, misc

    Bump...
    Post by: bryanbrown, Jan 15, 2018 in forum: Noonan Classifieds
  3. bryanbrown
    Post

    Racepak, Crower 10.7, misc

    Bump... Lencos are sold, couldn't figure out how to edit the title
    Post by: bryanbrown, Jan 4, 2018 in forum: Noonan Classifieds
  4. bryanbrown
    Thread

    Racepak, Crower 10.7, misc

    -Racepak Pro 1b with dash and spares- 3 analog boxes. Dash, ring gear rpm, engine rpm, egts, head temp, manifold temp, timing/phase (optic, crank...
    Thread by: bryanbrown, Dec 27, 2017, 5 replies, in forum: Noonan Classifieds
  5. bryanbrown
    Post

    Helmet fogging

    I re-routed the line inside the helmet so it's blowing straight up at the shield. I also put duct tape over my nose as a breath deflector and I...
    Post by: bryanbrown, Oct 27, 2015 in forum: Pit Buzz
  6. bryanbrown
    Thread

    Helmet fogging

    I need to get a new helmet this year and I'm wondering what helmets people have good luck with in regards to the shield fogging up. I've always...
    Thread by: bryanbrown, Oct 26, 2015, 9 replies, in forum: Pit Buzz
  7. bryanbrown
    Post

    A few issues for TA racers I would like to see addressed

    Is there actually anyone who decides NOT to buy/build an alcohol car because they'll have to go to ONE regional race before they get to run a...
    Post by: bryanbrown, Jul 6, 2015 in forum: Pit Buzz
  8. bryanbrown
    Post

    Blower starter cage

    I have one steel and one aluminum. There is no noticeable weight difference. I think the steel one holds up to abuse better also
    Post by: bryanbrown, Feb 26, 2015 in forum: PSI Superchargers Tech Questions
  9. bryanbrown
    Post

    Cage Shrouds/Aerodine

    I had no idea the seat pan couldn't be carbon. Considering that what you're doing makes sense. Personally I prefer to do as little welding...
    Post by: bryanbrown, Mar 31, 2014 in forum: Pit Buzz
  10. bryanbrown
    Post

    Cage Shrouds/Aerodine

    Why not just make the seat pan out of balistic carbon? That's seems like it would be easier to make, install and work around. I was planning on...
    Post by: bryanbrown, Mar 30, 2014 in forum: Pit Buzz
  11. bryanbrown
    Post

    Saturday Updates from Houston Regional

    Thanks for doing the updates Will. It's sad that as big as the sportsman series is and as much is money is spent from racers in all classes nhra...
    Post by: bryanbrown, Mar 9, 2014 in forum: Pit Buzz
  12. bryanbrown
    Post

    18 volts on a MSD system

    I use a 14.4v Makita battery, part number BL1430. I couldn't find one in a store, but they're easy to find online. I used 18v for a couple years...
    Post by: bryanbrown, Feb 25, 2014 in forum: PSI Superchargers Tech Questions
  13. bryanbrown
    Post

    Lateral head supports

    Butler Built is also an approved vendor. I have them and they work fine. I don't remember how much they were though http://www.butlerbuilt.net/
    Post by: bryanbrown, Jan 16, 2014 in forum: PSI Superchargers Tech Questions