Recent Content by billy438stroker

  1. billy438stroker
    Post

    ignition timing retards at revs

    I always wondered if it was lagging on the sensor' Since this Balancer has a long hub, that sticks the wheel out so far ... I can't believe how...
    Post by: billy438stroker, Jun 11, 2016 in forum: PSI Superchargers Tech Questions
  2. billy438stroker
    Post

    ignition timing retards at revs

    Its a almost new 7AL-3 Black ignition ...New MSD dist locked out.. MSD crank trigger
    Post by: billy438stroker, Jun 11, 2016 in forum: PSI Superchargers Tech Questions
  3. billy438stroker
    Post

    ignition timing retards at revs

    Haven't checked it.... Never seen a problem on a sbf... But msd said that none of that matters' running a crank trigger
    Post by: billy438stroker, Jun 11, 2016 in forum: PSI Superchargers Tech Questions
  4. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    Just got done installing the new msd bracket , but still same problem... One thing I made sure of is, when I rev the engine up' the more it...
    Post by: billy438stroker, Jun 11, 2016 in forum: PSI Superchargers Tech Questions
  5. billy438stroker
    Post

    ignition timing retards at revs

    I have a INNAVATORS WEST balancer and a MSD crank trigger... My timing retards as I take up the RPM'S ...The higher I take it, the more it...
    Post by: billy438stroker, Jun 11, 2016 in forum: PSI Superchargers Tech Questions
  6. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    I just noticed the crank trigger bracket is Vibrating pretty good , which is causing the timing mark not to be rock steady .... Now I wonder if...
    Post by: billy438stroker, Jun 6, 2016 in forum: PSI Superchargers Tech Questions
  7. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    Post by: billy438stroker, Jun 5, 2016 in forum: PSI Superchargers Tech Questions
  8. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    Yeah ' I lined one of the magnet's to the sensor with the balancer on 30* ..... turned the dist and lined it up with #1 ...Its a brand new dist...
    Post by: billy438stroker, Jun 5, 2016 in forum: PSI Superchargers Tech Questions
  9. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    I would believe that more.... I'm using a stock trans mount and a front motor plate & mid plate ... No motor mounts..
    Post by: billy438stroker, Jun 4, 2016 in forum: PSI Superchargers Tech Questions
  10. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    Haven't tried the dist' I know the wheel is more than tight, rechecked it twice.... The long bracket that the sensor bracket bolts to I had to...
    Post by: billy438stroker, Jun 4, 2016 in forum: PSI Superchargers Tech Questions
  11. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    I will recheck it but I think it holds at 28* instead of 30* at higher rpm's' but it may not....I will go back out and recheck it. It could be...
    Post by: billy438stroker, Jun 4, 2016 in forum: PSI Superchargers Tech Questions
  12. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    MSD tells me the dist or cam has nothing to do with it, where im running a crank trigger and its picking up timing off the crankshaft.. Is this...
    Post by: billy438stroker, Jun 4, 2016 in forum: PSI Superchargers Tech Questions
  13. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    [MEDIA] I'm still trying to chase this down.... You can see in this clip I just shot' It retards when I rev it , starting around the 12 sec mark
    Post by: billy438stroker, Jun 3, 2016 in forum: PSI Superchargers Tech Questions
  14. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    They are wired right' I even tried changing them , but then the timing would advance 15* or so when I would rev it, so I put them back like they...
    Post by: billy438stroker, Apr 21, 2016 in forum: PSI Superchargers Tech Questions
  15. billy438stroker
    Post

    Timing retarding 2* after installing crank trigger

    I will make a short video in a little while showing you what it is doing.... My balancer was off 2 * when bought new... Rechecked mark using a...
    Post by: billy438stroker, Apr 21, 2016 in forum: PSI Superchargers Tech Questions