Hemi Parts

Discussion in 'Noonan Classifieds' started by Joey Mackillican, Apr 8, 2021.

  1. Joey Mackillican

    Joey Mackillican New Member

    Joined:
    Jan 21, 2020
    Messages:
    22
    Likes Received:
    0
    -AJPE stage 5 TF zoomies with supports & EGT bunges (need to be refinished up 1 small dent) $325
    -Durabond Hemi cam Bearings look unused (PD-17) $25
    -Hemi 32 spline crank button- $75
    -Nostalgia fuel/Oil filter $25
    -Used MSD Promag 44 caps - two for $40
    - Erson Hemi 48 degree cam just polished believed to be 50mm can send photo of specs -$200
    -Edelbrock QWIK DATA logger (1 O2 Sensor,Drive Shaft, 2 pressure sensors and owners manual -$175
    - 4" Enderle fuel pump extention extra holes drilled $75

    Message for photos

    All prices are USD, OBO + Freight
     
    #1
  2. Joey Mackillican

    Joey Mackillican New Member

    Joined:
    Jan 21, 2020
    Messages:
    22
    Likes Received:
    0
    Have a bunch of Hemi Stuff still sitting around that ive collected make me an offer:

    - TF Stage 5 hemi Dragster Zoomies ( need to be cleaned up) -250$

    -Smith Brothers hemi push rods (3 sets of 8 10.326 x2 ,11.678 1 set of 17 10.326) - open to offers

    - Standard size Burst panel bracket & 1 panel $50

    -1 set of Dura 426 cam bearings $25

    -1 used 14mm RCD blower belt -1543-13.9-75 -$125

    -1 Used Gate 14mm blower belt - 14mgt-1400-125 (someone cut to 2") $40

    -1 Used RCD 11mm Blower belt -11m-1595-84ps $75

    -used Wilwood Master Cylinder 260-1304 $50

    -Edlebrock Computer with harness manuel O2, 2 pressure sensors & drive shaft $125

    - 32 spline 8 bolt Crank button $50

    -50mm Hemi Erson Cam ( no cam card) $200

    -Aero Supply filter -$25

    -8AN 3way shut off -$75

    -20 AN Right angle line fittings X2 -$30 ea

    -20 AN Straight line fittings x2 -$30 ea

    -20 AN oil pick up -$50

    -Box full of new/ used spark plug tubes - make offer

    All prices are USD + Freight

    PM me for photos or info
     
    #2
  3. bjrmg

    bjrmg New Member

    Joined:
    Jul 11, 2017
    Messages:
    28
    Likes Received:
    0
    Interested in headers, spark plug tubes. What else do you have. Jim R Houston Texas
     
    #3
  4. DCobeen

    DCobeen Member

    Joined:
    Sep 17, 2006
    Messages:
    49
    Likes Received:
    0
    Can you give me the specs on the 10.326" push rods, is this over all or down in the base of the cup. What Thickness, OD, tapered or straight, cup & ball size ?
    Mahalo Doug Cobeen
     
    #4
  5. Joey Mackillican

    Joey Mackillican New Member

    Joined:
    Jan 21, 2020
    Messages:
    22
    Likes Received:
    0
    what's your email i will send you spec sheet.
     
    #5
  6. DCobeen

    DCobeen Member

    Joined:
    Sep 17, 2006
    Messages:
    49
    Likes Received:
    0

Share This Page