Rodeck 481X2 block/short block parts, and pumps/mag/snout/drives/zoomies/Bird/gearset

Posting for a friend: Please contact him directly using the contact info at the bottom of the ad.

Pics of all of the below are viewable at: https://plus.google.com/photos/114453491960801668900/albums/6116601271561568497

All the parts on this list are spares from the existing engine combination in our 2000 Sterling 225 FED that we run in 6.90/7.00 Pro. They are cycled out parts with low runs, definitely serviceable even if you are running under 6.90

Rodeck TFX type 481X2 Cast Aluminum block with cross bolted mains, scalloped by Rodeck to be lightweight for Nostalgia Top Fuel. We ran it in blown alcohol FED, 6.90/7.00 Pro class
Standard BBC head configuration with extra stud in valley
.904 lifter bores
Oil gallies have restrictors and rear cam is double row ball bearing
Includes ARP 5/8 main studs, 1/2" head studs, and pan/front cover studs.
Has 1 window, professionally repaired
Also included are (8) 4.280 bore sleeves with fresh hone and o-ringed sleeves installed
$2700.00

parts that are specific for this 481X2 block are marked with asterisk *

*Dan Olson TFX pan for 481X2 block $375.00
*481X2 Cam Crane Billet Roller new $375.00 (cores for regrind are available, ask)
*Crower roller lifters .904 70 passes $300.00
*RCD 481X timing cover $250.00
*RCD 481X upper timing gear cover $125.00
*RCD 481X 11 hole timing gear $250.00
*RCD 481X crank gear BBC bore $80.00
*RCD 481X idler gear assembly stub shaft and needle bearing and gear $125.00
*RCD 481X 11 hole stub front drive adapter 5/8 hex female $125.00
*RCD 481X 6 hole 6” pump extension marmon type 5/8 hex shaft $90.00
RCD BBC crank hub double key with degree ring $80.00

BBC copper head gaskets (used) 4.280 - 4.500 bore, .040 - .100 thick, most around .060, these were used on block above and with o-ring in sleeves and receiver in head $35.00 set

Venolia Forged pistons (Qty 9), BBC 4.280 bore, 24 degree heads for 2.350 intake valve, 12:1 CR 1/16-1/16-1/8 ring, 1.090 pin (pins and buttons included) 120 passes with some new Akerly and Childs rings, all usable or spares, $300.00
C&A Deep Cycle forged rods (Qty 20), with ½” ARP bolts, 1.090 pin, Std. BBC big end, 6.620 length 60 passes. 2 rods are new unused $300

Rod/Piston combination for 4” stroke crank and 10.200 deck height, piston and rod assembly weight is 1927 grams

Enderle Bird aluminum injector hat, large shaft, with square barrel valve $800.00

BBC Snyper intake, unmolested, not modified $400.00

BBC Reactor flywheel, no ring gear, 1/2" bolts, no cert $75.00

BBC and SBC offset mag drives all new many configuration and tri drives with infinite clocking front mounts for any engine combination and accessory location
(Can be viewed at hainracing.com from) $675.00 to $1500.00

Billet Marmon clamps, New and Used, $60. - 85.

Blower snouts and couplers, from $75.

Mallory Super mag 3 generator, freshened by Mallory in 2003 and never ran since, includes case, cross drive or pin drive, coil, cap, and wires with spares $350.00

Waterman 7 gallon fuel pump with spare gears back from Waterman and flow card $500.00

Enderle 110 pump, older but fresh rebuilt from Enderle with card $280.00

Enderle 880 pump, few passes since new $375.00

9” Gearset, 4.33 large pinion, used 4 passes only, new in original box, PN 69-0161-1 $225.00


Contact: Leonard Hain, leonard@thehaincompany.com, (530) 295-8068. Parts are in Sacramento area

 

Sold items removed and bump

 

Bump please

 

Bump per policy

 

Bump it up please