526 cid Fathead engine parts package deal

I am clearing out my shop and trying to sell the remaining parts I have that fit my old combination so I can make room for the new pro mod stuff. That said, I will make someone a hell of a package deal as it will help pay off my pro mod quicker. This is an all or none deal for the most part, but I will consider taking a small item or two off if needed. Note these items are far from junk and I would run all of them if I didn't have brand new stuff coming. This was a complete motor and a friend bought it but he already had a lot of new parts he wanted to use so I kept them and here they are. This is a phenominal deal if you are new to a hemi or want to put together a fast motor and don't have a ton of money for the latest heads. These heads are about a tenth off the newest stuff from what I have seen.

All of these parts were a matched combination in a BAE billet +.100 tall block featuring a 60mm cam, .904 2" spread lifters, and 4.375" bore. This motor dynoed in at 2606 hp (Have dyno sheet) w/ a Kobelco K-11 roots blower.

What I have:

17 Spare 4.375" Sleeves for +.100 tall BAE Billet blocks (May fit others) I think they are all new, will dbl check for buyer. $50 per sleeve or all for $700

New -20 XRP oil line for Moroso billet wet sump pump to Moroso Dragster pan, XRP lightweight braided and factory crimped at XRP $100 (Paid over $158)

Matched 526 cid rotating assy
Bryant billet 4.375" crank w/ no cracks. std mains /.010 on 3 of the rod journals, std on the other rod journals
Set of New Clevite rod bearings matched to crank
8 New +.220 Brooks B2-L rods (Lightening rods sells them now)
8 New JE pistons+New Trend pins+ New pin buttons+New C&A/A&C rings between 12 and 12.5:1 cpr
3 spare new (Or very close) JE pistons
+any spare wrist pins, buttons, and rings that I have fit that setup.
$2,250

3 New Arias pistons $75

3 New Ross pistons $75

3 used Ross pistons $50

2 new Pins, 3 used pins of one design $50

12 new pins of a different design $150

8 Lightly used pins of a different design $75

bag of 12 sets of new pin Buttons pairs w/ a few used pairs for the Ross and Arias pistons I think $50

Another bag of aluminum and magnesium used pin buttons for the JE pistons I think $25

several boxes with rings (Some new, some low use and good for use in a pinch) $50

Billet tool steel bullet 60mm 4-7 swap cam, Hanna Specs, works well w/ screw or roots, It does have a few dings mostly on the outside edges of the journals. This does not effect operation and it was given a clean bill of health by Cantrel. $300

Sets of Crane .904 2" spread lifters just back from being inspected by Chase at Crane Cams.$200

Casale gear drive, Low runs. 14 hole vernier cam gear w/ hub for top fuel hex built in. Includes torrington bearing and shims. Very nice $350

BAE billet fuel pump extension w/ new hex drive and new bearing. Needs bushing or welding in the end as the bearing is loose. $100

2 New sets of Flatout head gaskets, 1 gasket has been torqued on a block for mockup with these heads and will work fine since it has not been fired. Other set is new in package $150

Total flow large valve billet fatheads (Like BAE 5 but slightly out flow them) Dual plugs w/ new block off plugs. Complete heads w/ all titanium valves, all studs, new lash caps, spare valves, keepers, and lash caps for $2,000 making them the most inexpensive set of fatheads on the net. Springs are at approx 400 lbs. These have had some repairs and will function perfectly. They just got back from Samsel's with a clean bill of health.

Box of spare titanium valves for use in a pinch (A few are nice) $50

BAE magnesium dual plug valve covers (Excellent shape) w/ 8 spark plug tubes, 8 Block off plugs, and billet tube retainers. $800


These were the already rock bottom prices I had these parts listed for.
$700
$100
$2,250
$75
$75
$50
$50
$150
$75
$50
$300
$200
$350
$100
$150
$2,000
$50
$800
--------------
$7,525

All of the above for $5,900+sh *package deal*

This is $1,625 off of my already rock bottom prices so be advised if you call and ask what my rock bottom price is I will hang up on you. Not being a jerk but tired of tire kickers who don't read the ad.

Call with any questions you may have and I'll be happy to answer them.

Trevor Sherwood
727-364-4368
Soldierboy0098@yahoo.com

 

Bump

Bump it up please