490 cu.in Noonan Long Block with Super 600's! ++

490 Cu.In. Noonan Hemi Front Drive Oil Pump

Long Block (No intake manifold): $32,000.00 USD

Short Block- $22,000.00 USD

Short Block (separate) $22,000.00

Noonan Billet Aluminum Hemi Block- 4.500” bore, 4.8 Spacing, .500” short deck, 65mm Cam, Front mount oil pump

8- sleeves –new last year re honed with a torque plate this year

1. 17 run Winberg Crank Shaft 3.900” stroke
   
   
2. Set of GRP connecting rods 6.830” - new
   

1. New Clevite rod bearings- V’s
   
   
2. New set of Clevite main Bearings – V’s
   

1- Set J&E Pistons- 4.500” – 17 runs (buttons inc.)

8- Trend M300 coated wrist pins with 17 runs

1- New set of Sealed Power rings (Hell Fire)

1- Used RCD gear drive with bearing support and titanium hub with degree wheel and magnets for crank trigger – 17 runs

1- Used fuel pump extension with shaft- polished

1. Used Bullet (Mark Brew) 65mm camshaft- cam spec sheet supplied-17 runs
   

1. Used set of Morale lifters 1.000” diameter- 17 runs
   

1. Used set of Trend Push Rods- 17 runs
   

1. Used Noonan oil pan -polished- quick disconnect fitting
   

1. Used Barnes Oil Pump 17 runs
   

1. Complete set of XRP Oil lines including quick disconnect oil pan line.
   

1. Shortened RCD Mag drive
   
   
   1. 
      
      

   ​

Spare parts included:

7- New Sleeves

5- (full Set) Main Caps

1. Timing cover
   

Cylinder Heads (separate): $8500.00 USD
Heads have 30 runs on them but many parts replaced 17 runs ago

NRE 2.560” intake valve, 1.900”exhaust valve

Manley Valves (30 runs)

Manley retainers (17 runs)

Manley Double springs 8 used intake (17 runs) 2.135” install height 530lbs, 8 used exhaust 2.135” 500lbs

Manley Lash-Loc valve keepers & lash caps – (17 runs)

All studs ready run



Long Block Comes With: $32,000.00 USD

1. 
   1 set of Manton Tool steel pushrods
   
   1 set of Manton intake and Reid exhaust rockers
   
   1 set of Williams valve covers with spray bars
   

​

Fuel Pump $1900.00 USD

1. Waterman Red .850 fuel pump (like new) with inlet and outlet. (Randy Anderson openings)
   

Ignition System $2000.00 USD

1-MSD 44 Pro Mag, coil and points box



Leanders Clutch $3500.00 USD

Comes with one used pack

 

Would you be interested in selling one set of the grp rods

 

Hello Brandon, thank you for the interest. I made the mistake of copying all my info on my motor and pasting it on this add. I can't seem to figure out how to edit it now?? lol
This is a complete motor minus the intake manifold, I would be willing to sell the short block separate or the heads separate, so I put all the details down. Its kind of a mess- sorry.
I also have a BAE motor with the exact same combo and the same heads. So IF someone wanted both sets of heads I would take them off my other motor.
One set of my heads are brand new!
I have a few sets of used rods I could sell cheap- they told me to put 35-40 runs on them I changed them every 15.
I went 5.51 @ 265 with this combo

 

I would also like to point out that this motor comes with everything. oil pump, lines, mag drive, spares and the down nozzles with the drop in jets for the $32k
Thanks again

 

would you be interested in selling the rockers

 

where are you located? thanks

 

I am in London ON. Canada. Willing to get into USA to certain race tracks

 

Sorry Hydrotheropy at this point I really do not want to separate this stuff. If someone asked about the heads then I would be interested. It is a great "complete piece" at a bargain if someone is looking for a top quality NEVER hurt engine.

 

New price on long block!
$28,000.00 with all the spares!

 

This is a great motor with nothing but the best!

 

Also have a BAE .500 tall deck manifold for sale $2500
JBR short injector with barrel valve flow meter and all lines -$4000

 

New price on Noonan long block!
$28,500.00 USD

 

Check your messages

 

Engine sold, still have lenco CS1 parts, Waterman Red fuel pump, MSD ignition system, JBR short screw blower injector with the barrel valve and all the lines, 2 Leanders clutches with extra discs and floaters

 

Do you still have the Leanders clutches?

 

Hi there, thanks for the reply. Yes I do still have the clutches for sale

 

Engine sold, still have fuel pump, ignition system, Leanders clutches, CS1 parts/ ratio, Short JBR injector with Barrel valve and lines.