Where to send my racepak flow meter to check or repair

Discussion in 'PSI Superchargers Tech Questions' started by kbhemi, Oct 24, 2021.

  1. kbhemi

    kbhemi Member

    Joined:
    Oct 14, 2003
    Messages:
    349
    Likes Received:
    2
    My flow meter and my Alky Pro is off by 1.8 gallons - when I should be 17 plus its showing 15.6 - Send to racepak or???? 316-761-7208 call or text - Thanks Wayne Roberts
     
    #1
    kbhemi, Oct 24, 2021
  2. rb0804

    rb0804 Active Member

    Joined:
    Aug 7, 2010
    Messages:
    671
    Likes Received:
    38
    Call Performance Data Systems. They have the ability to calibrate them.

    Todd Paton
    (949) 652-6300
     
    #2
    rb0804, Oct 24, 2021
  3. Dave Koehler

    Dave Koehler Member

    Joined:
    Sep 10, 2004
    Messages:
    443
    Likes Received:
    14
    just curious. How do you know it's off?
     
    #3
    Dave Koehler, Oct 24, 2021
  4. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    KBhemi, that’s not the flow meter that is off you need to calibrate Alky Pro so it matches the car and Racepak. I just got through writing a procedure on how to do it that has been checked by Alky Pro. If you send me your email address I can send it to you. My email is Mike.c@mindspring.com
     
    #4
    Mike Canter, Oct 24, 2021
    lucky devil likes this.
  5. kbhemi

    kbhemi Member

    Joined:
    Oct 14, 2003
    Messages:
    349
    Likes Received:
    2
    #5
    kbhemi, Oct 25, 2021
  6. drew556

    drew556 Member

    Joined:
    Jan 21, 2016
    Messages:
    55
    Likes Received:
    0
    Alky pro says it should have 17.3 gallons in the engine flow meter on the run says it has 15.6 off by 1.7 gallons
     
    #6
    drew556, Oct 26, 2021
  7. Dave Koehler

    Dave Koehler Member

    Joined:
    Sep 10, 2004
    Messages:
    443
    Likes Received:
    14
    Did you melt it down?
     
    #7
    Dave Koehler, Oct 26, 2021
  8. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    The flow meter is correct. You have to calibrate Alky Pro to match the flow meter. You had to do the same with the old Jetsize software.
     
    #8
    Mike Canter, Oct 26, 2021
  9. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    KBhemi it has been sent
     
    #9
    Mike Canter, Oct 26, 2021
  10. drew556

    drew556 Member

    Joined:
    Jan 21, 2016
    Messages:
    55
    Likes Received:
    0
    We did torch a head in Tulsa not horrible and trans ran out of air and was on the rev limiter @ 9800 in Texas we broke a rod but not sure of the cause yet but thinking lean and lots of timing might have detonated an knocked the bearings out
     
    #10
    drew556, Oct 26, 2021

Share This Page





XenPorta 2 PRO © Jason Axelrod from 8WAYRUN.COM