All kinds of stuff. For sale and wanted.

Chevy 6.3 Browell bell for a Bruno with a cert expired December 2017. Has some dings inside from a spacer that got loose. Has liner that fits 168 tooth flywheel and right side starter pocket. Comes in original shipping box. $1200

Coan 45/19 stator for 265mm Super mega converter. Three runs. $250
Coan 35/19 stator for 280mm Super mega converter. Some small dings from needle bearing. $250
Coan sprag for 280mm Pro Mod converter. $200

14mm HTD pulleys: 28 $65, 40 $80
14mm GT pulleys: 31 $70, 42 $80
13.9 HTD pulley: 40 $60

GT 8mm 1792-75PS used "purple" belt in good condition. $50
GT 14mm 1568-65PS used belt in good condition. $50

MSD 44Pro Mag Black earlier coil. $75

RCD external oil pump or external accessory drive with 31 tooth 5mm pulley. $150
http://rcdengineering.com/product/acc-drive-hub-w10-arbor-std-crank-sprocket
http://rcdengineering.com/product/31t-5mm-htd-acc-drive-sprocket

RCD external oil pump or external accessory drive 27 tooth 5mm pulley. $35

BBC Fowler dual slot idler bracket with 3.1" (75mm) crowned pulley that is 3.375" diameter.. Not much runtime. $300

BBC RCD Idler with outboard support and 3.1" pulley that is 3.2" diameter. $450

Crower BBC 4.25" crank double keyway and 1/2" front bolt.. Fresh back from Marine Crankshaft,.010/.010. $1500

Scat BBC 4.00 4340 crank, single keyway, 7/16" front bolt. Fresh .010/.010. $400

Littlefield 10.2 BBC Sq Port blower intake drilled for port nozzles with burst panel installed and has provisions for water. Almost new. $600

Pair of Fowler BBC sq port manifold spacers that are .255" thick with one end plate. This was originally used to put a 10.2" manifold on a 10.4" block. $100

3/4" thick Fowler lightened 2.500" setback plate for roots. Comes with blower studs and hold down bolts. $250

3/4" thick Fowler lightened 1.625" setback plate for roots. $225

1/2" thick Fowler lightened 2.500" set forward plate for PSI screw. Machined for o-ring. $250

Pair of Dart Ported 380cc Solid BBC heads. Titanium valves 2.300 in 1.88 ex, Manley NexTek 448 springs, Ti retainers. Have receiver groves in head. Comes with a complete set of T&D stainless 1.7 ratio rockets with all the stands and hardware. Low run count on these. $5,000 for all.

Pair of AJPE billet BBC conventional heads. Copper seats, Pac double springs, Ti retainers and Trick Tit valves. 2.350 in 1.88 ex. All AJ options. $8,000

Dan Olson four stage dry sump pan (three pickups) that fits a KB Olds, New Century and has recently been modified to fit a CN block. Has a couple of repairs but looks good. $400

Dunn 6 3/8" front offset mag drive with billet mag clamp. 3/8" for fuel pump, Dunn drive for mag. For a 5" extension and a 5/8" shaft. $650

Dunn 6 3/8" offset drive like above but this one has a Pro Mag 44 big cap instead of a Mag Drive. It's basically a distributor head that was used with an electronic ignition but that could be removed and you could use it as an offset mag drive. It mounts the fuel pump with a 3/8" hex. The drive uses 3/8" and can use pretty much whatever you wanted for an extension. This also comes with a set of MSD wires that have the Moroso shielding on them. $750

RCD front mag drive. Converts CW to CCW. $500.
http://rcdengineering.com/product/front-magneto-drive-38-cw-new-style

White Safety diaper for BBC with dry sump. Brand new with a mouse hole in it. $175

2 Complete large sprag assemblies with inter and outer races in good used shape along with the brass thrust washers. Only removed to replace with helicopter sprags. $400 ea.

DJ Safety SFI 7.1 carbon bucket for BBC with dry sump with inner liner and straps. Has had repairs and is heavier than new. $300

Pair of 3/8" thick 2.500" tube BBC header flanges. $50

Strange 9" 35 spline spool with bearings installed. P/N D-1555. $120

CS1 fine spline 1.25% with coarse drum. Was used with Bruno setup. $800

All prices plus shipping.

Selling for the wife of a friend that past. (224) 374-2786

 

If the Coan Pro Mod all aluminum converter does not sell let me know the price and where it will ship from.
Cheers
Bear

 

Sent you a message in your conversation/pm box, thanks.

 

Can I get pics of the valve covers with welded burn down tubes?

Hwhitlock@hitechcam1.com

Thanks

 

Can you send me a pic of this item?

cheyenne580@mchsi.com

 

Hi Tom please send me some pics of this item. If it has two 1/4 keyways the i can not use it. Mine crank snout only has one 3/16 and one 1/4 inch keyways.

Thanks

 

Tom would you sell it for $550.00 plus the key and shipped to 85119?

 

you have a PM

 

Is the BBC crank support still available?

 

ISO a RCD Crank Hub Installer/Remover 3/4-16" Crank Bolt Thread do you have one that you would sell. Thanx

 

Interested in the Simpson Hybrid Pro. What is the most recent cert date (or orig mfr date)? THANKS!

 

Do you still have the KB dry sump pan?

 

Would you take 200$ each for all set back plates you have if so I’ll take all of them

 

Is the White Safety diaper for BBC with dry sump still available?
If so please send pics to
bitsandpiecesfc@yahoo.com

Thanks Keith

 

Can you send me a pic of the roots set back plates please so I can see the opening. jon.quirin@toyota.com

 

Can you send some pictures of these heads?
Pair of Dart Ported 380cc Solid BBC heads. Titanium valves 2.300 in 1.88 ex, Manley NexTek 448 springs, Ti retainers. Have receiver groves in head. Comes with a complete set of T&D stainless 1.7 ratio rockets with all the stands and hardware. Low run count on these. $5,000 for all.

aafa760@gmail.com

 

Removed sold items and added some new.