Wheels, engine parts, converters, misc parts, tool tray, ect...

Wheels, engine parts, converters, misc parts, tool tray, Body, ect...

Parts that I have left.

New 48 Fiat Topelino coupe fiberglass body, got some damage in shipping that has been repaired but will need some sanding and a few chips fixed. Comes with new $250 Mckinney funny car body mounting kit still in the package. $500 buyer picks up or pays any crating and shipping charges

Funny car wheely bars, 1 set of single wheel 100" long w/ Taylor chute net, good shape just need a little cleaning cost $1,000+ new sell for $250 gets them out of my trailer, these are left over from the Tequila Patron/Kendal Oils FC I once owned and are perfectly usable.

GM Gen V Fully prepped and race ready Big block Chevy block, checked and not run since, ARP main studded, Filled, O-ringed, bore is 4.375" lt has 3 Heavy Duty Darton sleeves installed. It also has new cam bearings installed and a new torrington bearing for the cam gear. I have a timing cover with provisions for a fuel pump. It will hold 1450hp and was originally a 482 cid combo built by Doug Herbert for a tractor puller. We went to an aluminum block and later sold that motor so this is left over, this block is ready to run and my machinist can be called to verify. I run the hemi now so I have no use for this. This is a good usable block not junk. $500 You will have way more into prepping one for blown alcohol not including buying a block.

2 sets of Hoosier 34.5 *17*16 slicks, 14 and 21 passes on the sets $200 ea set

2 sets of Liners, 1 set has 0 runs, the other set had 2 or 3 runs on them. These are $155 a piece I will sell for $150 per pair. We have bead locks now and run 36" slicks.

****EVERYTHING ELSE IS FOR THE HEMI****

Blown alcohol torque converters:
Coan 11" (I think) weld together for a 1 1/4" Bruno drive $250

A used but good shape set of dragster upright zoomies w/ restraint brackets, pins, and new gaskets that fit BAE 4-5 heads (have had some small repairs but are not worn out, coating is off where small repairs where made. They are not bad looking right now. $350

12 Ross 4.375" pistons, 1.551 ch, 1.156 pin diam, 21.52 cc dome for BAE 6 fat heads, job number is 114537 About 14 runs on them in roots motor $300

7 Childs & Albert 4.310" pistons, 1.615 ch, 1.094 pin diam, dome cc unknown .610 tall. we believe Dart billet fuel heads again, These do have the step above the top ring land so a Veney head may be possible. Job number is 37159 and were made by Ross for C & A. May have came from Gene Snow. $150

6 JE 4.375" pistons, 1.094 pin diam, forging number 160, no job number listed so I have no clue what these fit shy of a hemi, if you know for sure please contact me, if you want them make an offer. These have a large dome and look to be a Veney or fuel head type piston $100

I have 32 1/2" head studs, Might be a set there for a KB stg 5 std deck block and fatheads if I remember right, 2 are pretty short, call for lengths. $500 for all. I will be checking the fit on these with my KB 5 mock up block as soon as I get a chance, I may also have head stud nuts I can sell for these.

nice FC tool tray w/ air log and fittings, has seperated slots for nuts and spots for specific tools $150

Pinion collar, between 3/4 to 7/8" wide aluminum w/ magnet $15

New PSI 1.5" inlet plate for psi roots blower, increases blower efficiency at lower overdrives (25-45%) Paid $200 sell for $75

New ERD 1 1/4" inlet plate for psi roots blower. Accomplishes inlet mod, very nice contouring, increases efficiency at mid range overdrives (30-50%). $100

New Moroso oil pan pickups #16, I have 2 of them $15 ea

*****************

Buyer pays Shipping.

Thanks,

Calling or emailing is best.
Trevor Sherwood
727-364-4368
Soldierboy0098@yahoo.com

 

tool & fuel tank

pic of tool tray & fuel tank


Tks Harry

bbfc394@aol.com

 

pm sent

pm sent

 

Can you send me pics of the fuel cell please.How many gallons?
Greg King
bodyhammer1@sbcglobal.net

 

hey trevor can you send me a couple of pics of the tool tray? thanks dave
620-249-5909

 

Bump it up please

 

Bump it up please

 

Pics of tool tray funnycar2400@gmail.com