Misc BAE & Alcohol Parts - Heads-Manifold-cams-lifters-hats-old chassis...etc

Misc Alcohol Parts - cams-lifters-buzzard hat- psi short hat....etc...

2 - Crane (LSM Core) - 60mm - 4-7 swap - 296/500-16 cams. Low runs - Just back from Crane for check/clean-up/regrind - ready to run - save big at only $425 each - or get the pair for $800

20 - Manton Cast Stainless intake rockers - 1.8 ratio ----> $90 each
10 - Reid pad style exhaust rockers- Hi Ratio ----> $149 each


Also --- 1 crank with above specs with crack above #2 main. Weld it up and run it in a non-supercharged engine. Hurry and make offer or she is off to the scrap yard. ---> $500 plus shipping


3 sets - Morel .904 lifters - 50 runs or less - never run in an engine that was hurt in any way. $350 per set


6 spares left - Hemi Crane Roller Lifters (66542) Std seat height , .904, have been used in 1.8-1.9 bore spreads, will not work in the 2" spread blocks. 25 hits or less. - $200


Mag Buzzard Injector with fuel block and lines. $800


Short FC style PSI Hat (End of shaft is slightly bent and has been bent since new, and worked fine) (They don't make these any more, so here is your chance to get a great used one)


Enderle dual offset mag drive (BELT), comes with single billet base that fits shaft assembly, no offset. (offer?)


NEW NEVER USED!!! 3 Taylor parachute restraints (will not work with our chassis and MW 11" rear)


Found some 1/2" head studs for a KB5 or KB6 - make offer before they go to the scrap yard



20 used GT - 8mm - 1600 - 75 - PS2 belts .... 8-11 runs .... $55 each


I will have pictures up on the website soon.


Thank you,

Contact: 9am-8pm (Mountain Time) 307.436.5610 (now is the time to call before we hit the road racing)

Kevin Hool
307.436.5610
Email: tafc562@hotmail.com
http://www.kandkmotorsports.com
http://www.twitter.com/kankmotorsports

 

Bump Please

To the top Please....Thanks!

 

To the top please...

Season is over so we'll be much easier to get a hold of....


Thank you,

 

check your private messages please

 

to the top ...

to the top please...

Updated list...

thank you,



Kevin Hool
http://www.kandkmotorsports.com
http://twitter.com/kankmotorsports

 

To the top please:

Updated list with some good stuff!

Thanks,


Kevin Hool

 

To the top please....


Some of these parts are headed to the scrap yard if not sold within the next week....make an offer if something catches your eye

Thanks,

Kevin Hool

http://www.kandkmotorsports.com
http://twitter.com/kankmotorsports

 

To the top please

Last few day for many of these parts..then to the scrap yard they go.

Make an offer now!

Kevin Hool

http://www.kandkmotorsports.com
http://twitter.com/kankmotorsports

 

To the Top Please ....

 

To the top please....

Thank you!

 

To the top please....Thank you

 

Can you bring the intake and exhaust rockers to Denver I am interested in them. Thanks. Geno

 

Hello Sir;
Are any of your crane 66542 lifters new or have fewer runs? Thanks
Len Howells

 

crane 904 lifters.any left?.crank and head studs going to the scraper how much.$$$ price is low on scrap!
psi shorty.best offer ???-250.00

 

Hey Guys/Gals....best way to reach us is email. On the road a lot and don't check the board that much during the season.

Crane Lifters: 20 runs - only 6 sets (12 lifters) left - $200 + shipping
Crank: scrap guys pay $250 for the Mallory...and they help us out because they love racing and think broken Hemi cranks are cool as lamp posts. Yes they drink alot!
Head studs: $100 + shipping
Short PSI Hat: our other one went for $950 - and this one will have to fetch at least that

Thanks

Kevin