New Price! TFX 96 short block for sale. Sorry for typo, that was wayyy off!

Selling the last of my Fuel head stuff. Reasonable offers considered.
6,500 obo.

Short block is not assembled. You are welcome to come inspect.

TFX 96 Cast block #679 2005 casting. Original 2005 Connie Kallita TF block (per AJPE). One window, repaired, three runs since repair. 3 run cam and main bearings included, fresh 4.310 hone for used pistons below..

Byrant 4.5 billet crank. Purchased new 11/07/13 sn# 44832, 3 1/8 runs, standard/standard. I paid 3,500 plus shipping. (receipt supplied)

8 MGP rods (I purchased new), 3 runs with 3 run bearings, data sheet included

1 new Brooks spare rod (came with motor purchase)

10 used Ross 4.310 pistons FUEL head (Veney). (8 are on above MGP rods with filed rings, new and filed for fresh hone, rods are stamped) 2 spare used and Ross build sheet included to order more if desired.

Rings, 2nd set, NIB rings, both sets of rings from AJPE receipt for NIB set included

8 extra 4.310 sleeves, purchased used from Tedder Pulling

22 studs. 9" long, 9/16 to 1/2 TFX head studs purchased used from Tedder Pulling (These are bottom row bolts that are spares, I don't have any other studs

2 alcohol cams

Mag gear drive and cover with oil pan rail 11 bolt cam gear

Extra Mag RCD/TFX front cover with oil pan rail piece.

Distributor base/oil pump drive with dunn X drive, (clamp and Mallory mag housing with rotor/cap available, no internals in mag)

Keith Black wet sump billet oil pump. New (3 run) -20 braided inlet line from pan to pump -12 filter in/out fittings.

Wet sump oil pan

2 sets used Morel 1 inch roller lifters (double roller exhaust wheel) 7 pairs are still in bag from Morel rebuild, one pair with 3 runs. Second full set is used, but wheels roll and are smooth.

Full set 3 run Smith Brothers 7/16 .120 pushrods for Morel lifers, data sheet included

1 set used Crane single roller lifters

13 3/8 intake used pushrods (8 good, can be used with either set of intake lifters)

8 used 3/8 pushrods for Crane single roller lifters

8 Stage 5 intake roller rockers, 7/16 adjuster, pressure feed to pushrod tip

1 extra rocker same as above, needs wheel replacement to be usable

2 Stage 5 intake roller rockers, 3/8 adjuster, non-pressure feed

Two factory Hemi intake rockers

Two new factory exhaust roller rockers with bronze shaft bushing, 3/8 adjuster (no adjusters, came in Chrysler box, I lost boxes)

8 Veney valve cover spark plug tubes, purchased from Tedder Pulling

Extra Scat billet 4.25 crank. Significant crack on number one throw. I was told it would be good after repair, but not good for C rotor screw applications. No other damage. Standard/standard.

Pics on request.

Thanks for looking
Scott Farley
502-608-0611
Iamaupspilot@aol.com

 

TTT, No reasonable offer will be refused.

 

New price. Serious typo, sorry. $6,500 or best offer.

Push rods and pistons are for fuel head. I have Ross piston information for these pistons and they did say they can make Fat Head pistons to go in this block, no problem.

Give me a ring, 502-608-0611
Iamaupspilot@aol.com

 

SIZE OF LIFTERS

 

One inch

 

A few bites, no takers. Make offer.

 

SOLD!!!!!! Thanks ITA!!